AMP-20341, AMP-20440 & AMP-20540 - Servo Amplifiers for DMC-21x3

  • Manufactured by: Galil Motion Control

Quick Overview

AMP-20341 4-axis 20 W Servo Drives
 

The AMP-20341 contains four linear drives for operating small brush-type servo motors.The AMP-20341 requires a ± 12–30 VDC input.* Output power is 20 W per amplifier or 60 W total.The gain of each transconductance linear amplifier is 0.1 A/V at 1 A maximum current.The typi..

Contact us

Description

AMP-20341 4-axis 20 W Servo Drives
 

The AMP-20341 contains four linear drives for operating small brush-type servo motors.The AMP-20341 requires a ± 12–30 VDC input.* Output power is 20 W per amplifier or 60 W total.The gain of each transconductance linear amplifier is 0.1 A/V at 1 A maximum current.The typical current loop bandwidth is 4 kHz.The AMP-20341 uses 15-pin D-sub connectors for encoder and limit connections on each axis and a 25-pin D-sub connector for I/O connections. 4.25" ´ 3.70".

 

AMP-204x0 2- and 4-axis 200 WServo Drives
 

The AMP-20440 contains four transconductance, PWM amplifiers for driving brush-type servo motors up to 200 Watts. Each amplifier drives up to 3.3 Amps at 20–60 VDC (available voltage at the motor is 10% less). No external heat sink is required.The AMP-20440 uses 2-pin Molex connectors for each motor and a 15-pin high density D-sub connector for encoder, limits and home for each axis. A single 44-pin high density D-sub connector is used for additional I/O signals.A 4-pin Molex is used for the DC voltage input from a single DC power supply ranging from 20–60 Volts. A two axis version, the AMP-20420 is also available. 4.95" x 3.75"

 

AMP-205x0 2- and 4-axis 500 W Servo Drives
 

The AMP-20540 contains four transconductance, PWM amplifiers for driving brushless or brush-type servo motors. Each amplifier drives motors operating at up to 7 Amps continuous, 10 Amps peak, 18–60 VDC (available voltage at the motor is 10% less). The gain settings of the amplifier are user-programmable at 0.4 Amp/Volt, 0.7 Amp/Volt and 1 Amp/Volt. The switching frequency is 60 kHz.The amplifier offers protection for over-voltage, under-voltage, over-current, short-circuit and over-temperature.The amplifier status can be read through the DMC-21x3 controller, and the BS command allows easy hall sensor set-up.A 2-axis amplifier board, the AMP-20520 is also available. In a standard configuration the DB-28040 I/O board will not install next to an AMP-20540, however the AMP-20540 provides 8 uncommitted analog inputs with 12-bit ADC (16-bit optional).* The SR-19900 shunt regulator is available for the AMP-20540. 6.92" x 4.85". CE certified

 


Datasheet (PDF file - 0.52 Meg)

 

Ask a question about the AMP-20341, AMP-20440 & AMP-20540 - Servo Amplifiers for DMC-21x3





Manufacturer Informations

Galil Motion Control
Manufacturer Website

    With over 750,000 controllers sold, Galil is a leading manufacturer of motion controllers and PLCs.
    Since introduction of the first microprocessor-based motion controller in 1983, Galil has remained one of the industry’s leading innovators. Located in Rocklin, California, Galil is a privately held company

    Other products